Metabo KSA18 LTX Bare Gebrauchs- und Pflegehandbuch PDF herunterladen (Seite 15)

ENGLISH

ENG

19 Locking screw (depth of cut)

20 Saw blade fixing screw

21 Outer saw blade flange

22 Saw blade

23 Movable safety guard

24 Inner saw blade flange

25 Lever (swivelling back the movable guard)

26 Capacity and signal indicator

27 Capacity indicator button

• Integral LED working light for illuminating the

cutting line

• Safety brake for stopping saw blade quickly

when switching off the machine.

• Electronic overload protector with integral

temperature monitor protects the machine and

the battery pack.

• Electronic single-cell monitor that extends the

service life of the battery pack.

Remove the battery pack from the machine

before any adjustment or maintenance is

carried out. Before fitting the battery pack, make

sure that the machine is switched off.

7.1 Battery pack

Charge the battery pack before use

(12)

If performance diminishes, recharge the

battery pack.

"Li-Power" li-ion battery packs have a

capacity and signal indicator: (26)

- Press the (27) button, the LEDs indicate the

charge level.

- If one LED is flashing, the battery pack is almost

flat and must be recharged.

Removal:

Press the battery pack release

(13)

button and pull

the battery pack

(12)

upwards.

Inserting:

Slide in the battery pack

(12)

until it engages.

7.2 Setting depth of cut

Loosen the locking screw (19). Read the depth of

cut that has been set from the scale (18). Tighten the

locking screw again.

It is advisable to set the depth of cut in such a way

that no more than half of each tooth on the saw

blade juts out under the workpiece. See illustration

on page 3.

7.3 Slanting saw blade for diagonal cuts

Loosen the locking screw (2). Tilt the motor part

against the guide plate (7). Read the angle which

has been set from the scale (1). Tighten the locking

screw again.

7.4 Correcting the saw blade angle

If, at 0°, the saw blade is not at right angles to the

guide plate: release lock nut (17) and correct saw

blade angle with adjusting screw (16). Then

retighten the lock nut.

7.5 Extraction connection piece / dust

ejection

Sawdust extraction:

connect a suitable dust extraction unit with suction

hose to the connection piece to extract the

sawdust. (6)

Sawdust ejection:

Turn the nozzle (6) to the desired position (away

from body if possible).

8.1

Automatic protection mode

If the machine switches off automatically, the

machine electronics have activated auto-

matic protection mode. A warning signal sounds

(continuous beeping). The beeping stops after a

maximum of 30 seconds or when the trigger is

released (5).

Causes and remedies:

Battery pack almost flat

(the electronics

prevent the battery pack from discharging

totally and avoid irreparable damage).

If one LED is flashing (26), the battery pack is

almost flat. If necessary, press the (27) button

and check the LEDs (26) to see the charge

level. If the battery pack is almost flat, it must

be recharged.

2. Long continuous overloading of the machine

will activate the

temperature cut-out

Leave the machine or battery pack to cool.

Note:

If the battery pack feels very warm, the

pack will cool more quickly in your "AIR

COOLED" charger.

Note:

The machine will cool more quickly if you

operate it at idling speed.

3. If the

current is too high

(for example, if the

6 Special Product Features

7 Initial Operation, Setting

8Use

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 107 108

Kommentare zu diesen Handbüchern

Keine Kommentare

Metabo KSA18 LTX Bare Gebrauchs- und Pflegehandbuch Seite 15

Kommentare zu diesen Handbüchern